Under the covers there’s a box full of lasers

In this post we’ll pull off the decorative trim and start to take a detailed look at what is in the box with a focus on the lasers.

The back of the sequencer has a power plug with two fuses and USB, serial, and camera connections.

IMG_3597 IMG_3598 IMG_3599

 

Removing the blue cosmetic trim panels (they simply pull off) reveals two filtered air intakes, one on each side of the instrument. There must be lots of other ways for air to get in to the sequencer as the instrument we bought had a bunch of dust bunnies in it and many of the parts inside had accumulated a fair amount of dust (evident in the pictures below).

IMG_3600 IMG_3601 IMG_3602

 

The panels on the sides and back are simply screwed on. Removing them reveals the guts of the machine. One side (on the left from the back) contains the imaging core, the lasers, and the main power supply. The other side (on the right from the back) contains the cooler, the pumps and actuator, and heated chamber for the fluidics, the stage controller, a USB hub and a USB to serial port converter, a 24 volt power supply, and one of only two customized circuit boards in the whole sequencer.

IMG_3608 IMG_3603 IMG_3604 IMG_3605 IMG_3607

 

The laser box contains the controller for the three lasers in the system (the focusing laser and the two TIRF excitation lasers). It is mounted on a shock absorbing mount which doubles as a heat sink to the side of the imaging core. Notice the dust collected on the cooling fan intake on the laser box – the filters on the sides on the GA IIx don’t appear to do a whole lot.

IMG_3613 IMG_3614 IMG_3609

 

The single fiber optic output of the laser box is fed into a shock mounted (the two metal plates have elastomers? between them) multimode scrambler which appears to be a re-branded General Photonics MMS-001B. It functions to generate a uniform and stable light distribution at the fiber output by literally squeezing a long strand of fiber optic at a high frequency in six directions. The output of the scrambler is used for TIRF illumination.

IMG_3612 IMG_3633 IMG_3634 IMG_3637

 

Removing the cover of the laser box reveals two lasers (a Laser Quantum GEM 500mW 532nm and a Melles Griot 85-RCA-400 660nm 400mW), each with a controller and a circuit board. Mounted on the circuit board is a Luminos 1×2 fiber optic switch and a Wavelength Electronics WLD3343 2.2A laser diode driver for the focus laser. The green and red lasers are connected to the 2×1 switch which controls which one is active. The output of the switch goes to the scrambler which ensures illumination uniformity.

IMG_3641 IMG_3632 IMG_3638 IMG_3639

 

Here are pictures of the lasers, the fiber optic switch, and the laser driver after disassembling the parts in the laser box.

IMG_3666 IMG_3645 IMG_3648 IMG_3656 IMG_3657 IMG_3664 IMG_3665

 

These class 3B (Melles Griot) and 4 (Quantum GEM) lasers are high power lasers. They can cause permanent vision loss in a fraction of a second. Even diffuse reflections from class 4 lasers can be eye hazards and these lasers are fire hazards! Please make sure that you familiarize yourself with laser safety (such as this excellent safety overview at Sam’s Laser FAQs) before attempting to use these lasers for any purpose other than as an integrated part of the Illumina GAIIx sequencer.

Detailed information (including pinouts, the RS232 command set, and images of both the laser and controller opened up) needed to operate the Quantum GEM 532 laser can be found here.  The RemoteApp laser control software for controlling the laser remotely can be downloaded from Laser Quantum here.

The  Melles Griot laser is apparently a custom laser but the controller is their standard universal laser controller without an enclosure. The manual for the L44000 controller contains pinout and command set information.

IMG_3646 IMG_3647

 

7 thoughts on “Under the covers there’s a box full of lasers”

  1. Did you get the 660nm laser running? I have one but can’t seem to get the controller to turn the laser on, I suspect I may be missing something

Comments are closed.